1. HOME
  2. Products
  3. On-demand InkJet Printing System
  4. Line Up
  5. CPQ

CPQ

CPQ7861
CPQ7861

CPQ model equipped with four print heads on its dedicated body, enables high-speed printing next to the CPE model. The alignment time is dramatically reduced by implementation of two CCD cameras. The vast print area covered by the four print heads enables printing on a 22.8 x 17” (580 x 430mm) substrate in as fast as 11 seconds surpassing CPi. Being equipped with two ink tanks, it is possible to use as a two-color printing model with a 2 head + 2 head configuration.

Specifications
Max. Panel Size31.3 x 25.6” (795 x 651mm)
Max. Discharge
Frequency
45kHz
X-axis resolution (dpi)360 / 720 / 1080 / 1440
Y-axis resolution (dpi)360 / 720 / 1080 / 1440 / 1800 / 2160
Min. Droplet size6pl / 13pl
Number of nozzles4 x 1024 (4096)
Standard resolution720dpi
Min. line width *170µm - 90µm
Speed *222.8x17"
(580x430mm)
11 seconds
24x20"
(610x510mm)
11 seconds
30.7x24"
(780x610mm)
20 seconds
Number of ink tank1
Ink Tank Volume (Max.) 2000ml
On-Head UV LampLED-UV lamp
Camera Resolution11.8 x 9.0mm
Air supply:Pressure0.5MPa
Air supply:Consumption5.4ft³/min. (150ℓ/min.)
Power supply*3Single Phase 200-240V 20A 50/60Hz
Weight2932 lbs. (1330kg)
Dimensions
[ unit: inch(mm) ]
Dimensions (CPQ7861)
*1 Depends on ink *2 While using UV pinning type ink, speed spec may change according to required UV energy. Print times do not include image alignment, shuttle and load and unload time. Please confirm the printing quality and speed by allowing us to run a benchmark test at MicroCraft. *3 Separate power source for cooling device and vacuum pump is necessary (specifications may be different in some countries).
[CraftPix Series Operating Conditions] · 70-75°F (21-24°C), 30-70% relative humidity · Free of moisture, dust (ISO class 7 (FED-STD-209D Class10,000) clean room or better), vibration, and corrosive gas. · Atmospheric Dew Point: -14°C or below (at 0.7Mpa, dew point is 15°C or below) · Oil Mist Concentration: 1mg/㎥ (ANR) or below
§Replacement of ink requires special training §CraftPix consumables are ink, cleaning fluid, filter, sending fluid tube, UV lamp, array unit, vacuum paper, temperature sensor, heater, etc. §Please contact MicroCraft for detailed specification.
CraftPix General Specification
Board Thickness0.004" to 0.24" (0.1-6mm)*
† compatibility for thickness exceeds 0.24”(6.0mm) is optional
AlignmentCCD Camera
MonitorLCD Monitor
SoftwareWindows 7 / Windows 8 / Windows 10
Data Input FormatRS274X, RS274D, ODB++, DPF, DXF, BMP**, TIFF**
* When the vacuum table is used. Figures depend on the board warpage and clamp type. Printing quality may decrease with warpage. Please contact MicroCraft for more precise figures for specific conditions. ** Scaling and alignment functions are not usable.
Vacuum Pump
Power SupplyThree Phase AC200V 10A 50/60Hz, AC220V 10A 60Hz
Capacity50Hz: 20.7ft³/min. (575ℓ/min.)
60Hz: 24.7ft³/min. (685ℓ/min.)
Air Coupler SizeRC 3/4
Weight187.4 lbs. (85kg)
List of Supported Ink
Legend Ink
AGFADipamat Legend ink Wh04
Dipamat Legend ink FWh01
Dipamat Legend ink Bl01
Dipamat Legend ink Ye04
CUR-BFI 001
TAIYO INK MFG. CO., LTD.
(TAIYO HOLDINGS CO., LTD.)
IJR-4000 MW301N, IJR-4000 MW301SW*
IJR- 4000 MW410, IJR- 4000 MW500
IJR- 4000 EM100, IJR- 4000 FB100E
IJR- 4000 FW300, IJR- 4000 YM200
Etch Resist Ink
AGFADipamat Etch Resist ER01
Goo Chemical Co., Ltd.GIP- 410, GIP- 500, GIP- 520, GIP- 605
*Product name changed from PER to GIP.
TAIYO INK MFG. CO., LTD.
(TAIYO HOLDINGS CO., LTD.)
IJR-3000 GE100
MacDermid Incorporated.CircuitJet 200
Plating Resist Ink
Goo Chemical Co., Ltd.GIP-700
*Product name changed from PER to GIP.
TAIYO INK MFG. CO., LTD.
(TAIYO HOLDINGS CO., LTD.)
IJR-3000 BE100
Solder Resist Ink
AGFADipamat Soldermask SM G01
TAIYO INK MFG. CO., LTD.
(TAIYO HOLDINGS CO., LTD.)
IJSR-4000 JM01E, IJSR-4000 JM01C
IJSR- 4000 JM02G
MicroCraft K.K.MPJ101-SG20
MPJ101-SG10, MPJ101-SC10
MPJ101-SK10, MPJ101-SW10
MPJ101-SR10, MPJ101-SB10
MPJ101-FG20
MPJ101-FG10, MPJ101-FC10
* Please contact MicroCraft for further details.